fixing kc556b slides
Posted: Sat Feb 21, 2015 10:08 pm
So I went to a few stores looking for steel strapping/banding. I thought it was a good idea but I guess the times are a changing....only plastic nowadays! I decided that I would try using an old hacksaw blade and grind off the teeth to make a slide removal tool. I put the blade into a vise and ground the teeth
![Image](http://imagizer.imageshack.us/v2/800x600q90/908/T0I3Jg.jpg)
worked great as long as you use a good quality blade, a cheap one shatters when you try to bend it slightly on the end like you need to do to make the tool.
Here is both sides of an original stop
![Image](http://imagizer.imageshack.us/v2/800x600q90/661/Y04z1K.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/633/d8h6k8.jpg)
While I was making the tool I saw the hole at the end of the blade and thought it looked close to the same size as the hole in the slide. I ground the blade to size and length
![Image](http://imagizer.imageshack.us/v2/800x600q90/537/ikNDAr.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/538/fviG6U.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/673/u4cweO.jpg)
Give it a slight bend to match the original stop
![Image](http://imagizer.imageshack.us/v2/800x600q90/661/acHdsQ.jpg)
The new piece goes through the hole and I used a nail as a rivet
![Image](http://imagizer.imageshack.us/v2/800x600q90/912/SWPrAr.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/538/5f9wrc.jpg)
The "rivet" has to be peened quite flat or the drawer won't close properly. I used a punch with a 1/4" round flat end to flatten the nail and ended up using my 16 oz finishing hammer to pound it flat enough. I used a scrap piece of 1/4" flat stock under the rivet head while peening.
I fixed 4 slides and my box is working like new again!
Richard
![Image](http://imagizer.imageshack.us/v2/800x600q90/908/T0I3Jg.jpg)
worked great as long as you use a good quality blade, a cheap one shatters when you try to bend it slightly on the end like you need to do to make the tool.
Here is both sides of an original stop
![Image](http://imagizer.imageshack.us/v2/800x600q90/661/Y04z1K.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/633/d8h6k8.jpg)
While I was making the tool I saw the hole at the end of the blade and thought it looked close to the same size as the hole in the slide. I ground the blade to size and length
![Image](http://imagizer.imageshack.us/v2/800x600q90/537/ikNDAr.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/538/fviG6U.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/673/u4cweO.jpg)
Give it a slight bend to match the original stop
![Image](http://imagizer.imageshack.us/v2/800x600q90/661/acHdsQ.jpg)
The new piece goes through the hole and I used a nail as a rivet
![Image](http://imagizer.imageshack.us/v2/800x600q90/912/SWPrAr.jpg)
![Image](http://imagizer.imageshack.us/v2/800x600q90/538/5f9wrc.jpg)
The "rivet" has to be peened quite flat or the drawer won't close properly. I used a punch with a 1/4" round flat end to flatten the nail and ended up using my 16 oz finishing hammer to pound it flat enough. I used a scrap piece of 1/4" flat stock under the rivet head while peening.
I fixed 4 slides and my box is working like new again!
Richard