Double and triple date codes

This is the place to ask questions about specific tools. Please search for other questions about your subject before you post a new one... it may already be here. Also, please include pictures if possible to make identification easier.
Forum rules
Please make sure you've read the Rules and Etiquette Page, which spells out the rules and guidelines of this forum.
snapmom
Posts: 1127
Joined: Sun Oct 17, 2010 2:38 pm
Contact:

Double and triple date codes

Post by snapmom »

Why were there double and triple date codes? One theory is that they were used as part of the guarantee system, that the salesman would mark it on the year sold. I think this theory does not hold up. The one year guarantee was abandoned in about 30/31. Most all doubles I have seen are during or after 30. Also that theory does not account for triple date codes.

Most double date codes are 30/31 and 34/35. I cannot remember seeing one with a pre 29 date. doubles after 35 are rare.
The intial date code was stamped with a machine.

So why the doubles, I just don't know. Any ideas out there, any facts?
Image
Image
Image
chad s
Posts: 33
Joined: Wed Oct 20, 2010 5:20 am
Contact:

Re: Double and triple date codes

Post by chad s »

snapmom wrote:
Most double date codes are 30/31 and 34/35. I cannot remember seeing one with a pre 29 date. doubles after 35 are rare.
The intial date code was stamped with a machine.
I'm pretty sure I have a screwdriver bit stamped 27 and 29, if that counts as being pre 29.
Last edited by chad s on Mon Oct 25, 2010 5:54 pm, edited 1 time in total.
snapmom
Posts: 1127
Joined: Sun Oct 17, 2010 2:38 pm
Contact:

Re: Double and triple date codes

Post by snapmom »

Post a pic.
chad s
Posts: 33
Joined: Wed Oct 20, 2010 5:20 am
Contact:

Re: Double and triple date codes

Post by chad s »

Image
madprofessor
Posts: 18
Joined: Thu Oct 21, 2010 9:07 pm
Your Location: Virginia Beach
Contact:

Re: Double and triple date codes

Post by madprofessor »

That's a beauty Chad.
chad s
Posts: 33
Joined: Wed Oct 20, 2010 5:20 am
Contact:

Re: Double and triple date codes

Post by chad s »

madprofessor wrote:That's a beauty Chad.
Thanks. Making a complete set of both the long and short versions of these is time consuming. I have close to a complete set, but am probably missing 2, and some of them are sort of place holders as the tips sometime turn up with being filed down after being damaged.
chad s
Posts: 33
Joined: Wed Oct 20, 2010 5:20 am
Contact:

Re: Double and triple date codes

Post by chad s »

chad s wrote:
madprofessor wrote:That's a beauty Chad.
Thanks. Making a complete set of both the long and short versions of these is time consuming. I have close to a complete set, but am missing 2 or 3, and some are an in between length, so there actually three lengths of these that were made. Some of them are sort of place holders as the tips sometime turn up with being filed down after being damaged.
Tim_NC
Posts: 5
Joined: Thu Oct 28, 2010 5:22 am
Contact:

Re: Double and triple date codes

Post by Tim_NC »

Could this be the moment in time that the date code tooling was changed and the operator just struck it to test? Of inadvertently picked the wrong tooling and found it after test? Just some thoughts.
Frank Murch
Site Admin
Posts: 247
Joined: Wed Oct 13, 2010 6:34 pm
Your Location: San Diego
Contact:

Re: Double and triple date codes

Post by Frank Murch »

Excellent discussion
oldtom
Posts: 6
Joined: Tue Dec 14, 2010 5:18 pm
Contact:

Re: Double and triple date codes

Post by oldtom »

wot about when snopon shut down or at least slowed down production in the early 80 did they stop making some items and remark on date released =shipped from manufacturing plant would make more sense in the 1930 but with snapon, ?
Post Reply

Who is online

Users browsing this forum: Ahrefs [Bot], Semrush [Bot] and 137 guests